[Q12-Q35] Get 100% Real H35-480_V3.0 Accurate & Verified Answers As Seen in the Real Exam!

Rate this post

Get 100% Real H35-480_V3.0 Exam Questions, Accurate & Verified Answers As Seen in the Real Exam!

H35-480_V3.0 Premium Files Updated Mar-2023 Practice Valid Exam Dumps Question

QUESTION 12
Which of the following NR channels or signals supports static and dynamic power control?

PDCCH

PUSCH

PBCH

QUESTION 13
C-band is the most popular frequency band for 5G network deployment. However, there is an imbalance between uplink and downlink coverage – how much does this imbalance approximately amount to?

5dB

3dB

12dB

20dB

QUESTION 14
What are the typical sizes of ping packets and intervals in single site verification?

1500bytes, 2s

1500 bytes,1s

32 bytes,1s

32 bytes, 2s

QUESTION 15
The RSRP value of the test terminal can be viewed on the GENEX Probe. Which of the following test results indicate good signal quality?

30 to 60dBm

-60dBm to -90dBm

0 to 60dBm

-30 to -60dBm

QUESTION 16
During a 5G test, a portable computer is directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic IP address for communication.

True

False

QUESTION 17
Which of the following MML commands can be used to query version information relating to the software stored on the gNodeB?

LST VER

DSP SOFTWARE

LST SOFTWARE

LST PATCH

QUESTION 18
During single site verification, which of the following messages can be traced by the Probe to analyze problems?

L3 Messages

Xn Messages

L1 Messages

NG Messages

QUESTION 19
What is the maximum number of PCIs supported by a 5G network?

1008

512

768

384

QUESTION 20
Which of the following is the recommended sequence for configuring data during gNodeB commissioning?

Transport data – Radio data – Device data – Basic data

Device data – Transport data – Radio data – Basic data

Basic data – Radio data Device data – Transport data

Basic data – Device data – Transport data – Radio Data

QUESTION 21
Which of the following statements about the NR slot structure are correct? (Choose All that Apply)

Downlink slots can only be used to transmit downlink data.

Downlink self-contained slots can be used to transmit uplink data and SRSs.

The number of symbols in one slot is fixed to 14 regardless of the subcarrier spacing configuration.

The symbols in a slot can be classified as downlink, uplink, or flexible.

QUESTION 22
Which of the following NR channels or signals supports static and dynamic power control?

PDCCH

PUSCH

PBCH

QUESTION 23
What is the required distance between a CPE and a gNodeB in a 5G network test?

Less than 10m

Greater than 5m

Less than 5m

Greater than 10m

QUESTION 24
Which downlink data split modes are supported on the gNodeB side in the 5G NSA Option 3x architecture?

MCG_ONLY: only split to the MCG

SCG_AND_MCG: static data split

SCG_ONLY: only split to the SCG

SCG_AND_MCG: dynamic data split

QUESTION 25
Which of the following actions are involved in NAS procedure management in 5G? (Choose all that Apply)

Registration management

RRC reestablishment

Session management

RRC connection setup

QUESTION 26
Which of the following signals is measured by a 5G UE to report channel quality information such as the CQI, RI, and PMI to a gNodeB?

SSB SINR

CSI-RS SINR

SSB RSRP

CSI-RS RSRP

QUESTION 27
5G wireless network cloudification can significantly improve the user rate.

True

False

QUESTION 28
Which of the following functions are implemented by the UBBP board in the BBU5900? (Choose all that Apply)

Provides CPRI ports for communication with RF modules.

Manages the configuration and devices for the base station.

Monitors performance and processes signals for the base station.

Processes uplink and downlink baseband signals.

QUESTION 29
What is the maximum MIMO mode supported by Huawei 5G indoor CPE?

4T8R

2T2R

2T4R

4T4R

QUESTION 30
The mmWave range is new for NR. It supports the largest bandwidth in a cell but has poor coverage capabilities. It requires high performance from RF components and generally applies only to line of sight (LOS) coverage.

True

False

The mmWave range is a new spectrum range for 5G NR, and it supports the largest bandwidth in a cell. However, it has poor coverage capabilities, as it requires high performance from RF components and generally applies only to line of sight (LOS) coverage. This makes it challenging to use in many applications, as it requires careful planning and implementation in order to ensure effective coverage.
https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/
5G Implementation Guidelines: NSA Option 3 – Future Networks
https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/
https://www.ericsson.com/en/ran
5G RAN – Radio Access Networks – Ericsson
https://www.ericsson.com/en/ran
https://www.5gamericas.org/wp-content/uploads/2020/12/InDesign-Understanding-mmWave-for-5G-Networks.pdf Understanding mmWave for 5G Networks 1 – 5G Americas
https://www.5gamericas.org/wp-content/uploads/2020/12/InDesign-Understanding-mmWave-for-5G-Networks.pdf The millimeter wave (mmWave) range is new for 5G NR (New Radio). It supports the largest bandwidth in a cell but has poor coverage capabilities. It requires high performance from RF components and generally applies only to line of sight (LOS) coverage.
The mmWave range is considered to be the higher frequency range of the 5G spectrum and it includes frequencies above 24GHz, such as 28GHz, 38GHz and 60GHz. These frequencies offer a large amount of bandwidth, which is necessary to support high-data rate services, such as ultra-high-definition video streaming, virtual reality, and the internet of things.
However, the mmWave range has poor coverage capabilities because the signals are easily blocked by obstacles such as buildings and trees, and they also have a shorter propagation distance than lower frequency bands. Therefore, mmWave range is generally used for high-density urban areas, and indoor environments.
Additionally, RF components for mmWave have to meet high performance requirements, such as high linearity, high gain and high power handling capability. Also, the mmWave signals are highly sensitive to the presence or absence of a clear line of sight (LOS) between the transmitter and the receiver, which makes it less reliable for non-line-of-sight (NLOS) coverage.

QUESTION 31
Which of the following statements about the functions of an AAU are correct?

Up/down conversion of spectrum

Power amplification

Signal filtering

Baseband data processing

Analog-to-digital/digital-to-analog conversion

QUESTION 32
In the inter-site DC solution, the X2 interface can be used to implement transmission interconnection between the LTE and NR sites. Which of the following is the requirement of the transmission delay in such case?

<40ms

<10ms

<30ms

<20ms

QUESTION 33
Which of the following is the correct sequence for adding gNodeB hardware?

RF unit -> Subrack -> Board -> Cabinet

Board -> Cabinet -> Subrack -> RF unit

Cabinet -> Subrack -> Board -> RF unit

Subrack -> Board -> Cabinet -> RF unit

QUESTION 34
At which layer is downlink data split implemented over the NR air interface in the NSA Option 3x architecture?

RLC layer

MAC layer

PDCP layer

Physical layer

QUESTION 35
Which of the following messages is the first message sent by a gNodeB to an AMF?

NGAP_UL_NAS_TRANSP

RRC_SETUP

NGAP_INIT_CONTEXT_SETUP_RSP

NGAP_INIT_UE_MSG

REAL H35-480_V3.0 Exam Questions With 100% Refund Guarantee : https://www.troytecdumps.com/H35-480_V3.0-troytec-exam-dumps.html

High-quality Troytec review files

[Q12-Q35] Get 100% Real H35-480_V3.0 Accurate & Verified Answers As Seen in the Real Exam!

troytecdumps

Leave a Reply Cancel reply

Related Posts

H12-711_V4.0 Tested & Approved Huawei Certified ICT Associate Study Materials [Q19-Q37]

Get Instant Access to H19-401_V2.0 Practice Exam Questions [Q39-Q61]

Get Special Discount Offer of H19-308-ENU Certification Exam Sample Questions and Answers [Q69-Q86]

troytecdumps

Leave a Reply Cancel reply