CCME Real Exam Questions and Answers FREE 156-836 Updated on Oct 02, 2024 [Q31-Q50]

5/5 - (1 vote)

CCME 156-836 Real Exam Questions and Answers FREE Updated on Oct 02, 2024

156-836 Ultimate Study Guide – TroytecDumps

QUESTION 31
Which command is used to set the number of sites in a Maestro environment?

set maestro orchestrator-site-amount

set maestro configuration orchestrator-site-amount

set maestro configuration orchestrator-site-number

set maestro configuration orchestrator-site-id

QUESTION 32
To display processes that are consuming excessive system resources, users should use the_____ command.

asg perf -v

asg stat -v

top

asg_perf_hogs

QUESTION 33
In case of Correction, where is information about Owner stored?

In Correction table of Target Appliance

In Connection tables of all Appliances participating in Correction Layer flow

In Correction tables of all Appliances participating in Correction Layer flow

In Connection table of Target Appliances

QUESTION 34
What is the Correction Layer mechanism?

Ensures asymmetric traffic is handled properly, especially in the case of NAT or VPNs.

The load-balancing mechanism used by the MHO.

The MHO’s distribution algorithm which determines the handling SGM for a given connection.

Enforces the access policy on the SGMs and synchronizes the enforcement verdict to other SGMs in the SG.

QUESTION 35
While looking at your system’s correction statistics, you notice you have a correction rate approaching 100 percent. Is this a problem?

A correction rate above 90 percent indicates a need to disable Layer 4 Distribution.

A correction rate approaching 100 percent of all connections is unusual. This is a cause for concern because the SGMs may fail to process traffic.

If correction rates are higher than 80 percent, latency is expected.

In some scenarios, a correction rate approaching 100 percent of all connections is not unusual. This is not usually a cause for concern as the correction mechanism is fast and efficient.

QUESTION 36
What does the lldpctl command do?

Show all devices discovered by LLDP protocol on downlink ports

Show all devices discovered by LLDP protocol on all ports

Discover orchestrators

Show all devices discovered by LLDP protocol on uplink ports

QUESTION 37
Which command should be used to restart Orchestrator service only?

orchd restart

reboot

service orchestrator restart

cpstop; cpstart

QUESTION 38
HealthCheck Point _____

is a self-updatable suite of tools for MHOs with the capability to assess the health of the system and provide a timeline of critical and informative events that might have occurred in a production system.

performs a system health check and is meant to replace both a CPInfo and the health check script.

can be used to let you visualize the Firewall topology for the SG and view live statistics, which includes throughput, problem notes, and CPU utilization.

is a self-updatable suite of tools for SGMs with the capability to assess the health of the system, visualize the Firewall topology, provide a timeline of critical and informative events that might have occurred in a production system.

QUESTION 39
Possibilities for a failure in a single SGM of a Security Group include.

A change was made with clish instead of gClish, causing the SGM to handle traffic differently than the other SGMs.

SecureXL is not enabled on the SGM.

An administrator imported a hotfix into the CPUSE repository of a single SGM.

There are too many active SGMs in the SG.

QUESTION 40
What cannot be learned from the output of asg monitor command?

Uptime

Port status

Security Policy status

Appliances cluster status

QUESTION 41
What is the maximum number of Appliances within Security group in Dual-Site configuration?

QUESTION 42
What cannot be learned from the output of lldpctl?

Serial number of Appliance

Appliance model

Distribution mode

Orchestrator’s IP

QUESTION 43
At a minimum, how many management and Uplink ports does a SG require?

Only one of the two interfaces is needed for the Security Group.

Neither are required.

Two of each.

One each.

QUESTION 44
What happens when you make changes from Clish on the SMO Master?

The changes are synchronized to the SMS/MDS as a backup.

The changes are synchronized to the MHO as a backup.

Changes are only applied on the SMO Master.

Changes are applied to all members in the SG.

QUESTION 45
What is a security group?

A solution for Security Gateway redundancy and Load Sharing.

A set of appliances of the same model that are collectively managed by the MHO.

A set of network interfaces and individual SGMs assigned to a logical group.

A set of objects in SmartConsole that are responsible for enforcing an access policy.

QUESTION 46
Which feature is used to force trusted non-F2F traffic into the fully accelerated path for handling by SecureXL.

Fast Accelerator

hypersync

rate limiting

SecureXL

QUESTION 47
What kinds of transceivers are supported on Orchestrator MHO-170?

SFP, QSFP, QSFP28

SFP+, SFP28, QSFP

SFP, SFP+, SFP28

QSFP, QSFP28

QUESTION 48
Where should sx_api_ports_dump.py command be ran?

Management server

Security Group

Orchestrator

SMO Appliance

QUESTION 49
How many orchestrators may Dual-Site include?

2 or 4

Only 4

QUESTION 50
Which blade configuration files should be backed up on the SG if upgrading from R80.30SP or earlier?

IPS configuration files

fwkern.conf files.

VPN configuration files

Mobile Access configuration files.

CheckPoint Certified Maestro Expert (CCME) certification exam is designed for professionals who want to validate their expertise in deploying and managing Check Point Maestro solutions. Check Point Maestro is a hyperscale network security solution that enables organizations to expand their security capabilities as their networks grow. The CCME certification exam is intended for those who have already earned the Check Point Certified Maestro Administrator (CCMA) certification and want to prove their advanced knowledge and skills in managing and troubleshooting Check Point Maestro environments.

The CCME certification exam consists of 90 multiple-choice questions that need to be completed within 180 minutes. 156-836 exam is available in English and Japanese languages. The passing score for the exam is 70%, and candidates who pass the exam will receive a certificate of achievement from Check Point.

Ultimate Guide to Prepare 156-836 Certification Exam for CCME: https://www.troytecdumps.com/156-836-troytec-exam-dumps.html

High-quality Troytec review files

CCME Real Exam Questions and Answers FREE 156-836 Updated on Oct 02, 2024 [Q31-Q50]

troytecdumps

Leave a Reply Cancel reply

Related Posts

CheckPoint 156-835 Practice Exam – 66 Unique Questions [Q24-Q46]

100% Reliable 156-835 Exam Dumps Test Pdf Exam Material [Q17-Q40]

[Jan-2023] Valid Way To Pass CheckPoint Exam Dumps with 156-560 Exam Study Guide [Q18-Q33]

troytecdumps

Leave a Reply Cancel reply